¶ Safety Signs
| Safety sign types | Hazard Statement |
|---|---|
 |
High temperature surface: indicates that the component will generate high temperature. Pay special attention when working around the high temperature component. Be careful when handling components to avoid burns. Allow components to cool to a safe temperature before handling. |
|
| High voltage: The high voltage sign indicates that there is a high voltage circuit in the location. Please disconnect the power during maintenance. |
|
| Squeezing parts: Squeezing Note: This part is prone to squeezing risk around it. Please pay special attention when operating. Do not put your head, hands or other things into the dangerous area. |
| 
| Grounding mark: RMS220 requires a dedicated AC circuit and reliable grounding. |
|
| Wear goggles: The laser beam is extremely harmful to the eyes and skin, which may cause permanent blindness. You must wear goggles. |
|
| Wear gloves: The printing chamber is designed to operate at temperatures up to 220°C. Do not perform any operations until the surface temperature is<50°C. When removing an uncooled model, wear heat-resistant silicone gloves. |
|
| Wearing a mask: A protective mask must be worn when handling powder.|
|
| Read the manual: Always refer to the relevant instruction manual/instruction manual before operating any equipment or machine. This is to prevent accidents or injuries that may occur due to unfamiliarity with necessary procedures or dangerous conditions. |
|
| Do not open by non-professionals: This sign indicates that this panel must not be opened by non-professionals, as opening it is dangerous. |
¶ Safety Regulations
Please read the safety information to ensure that you use this equipment safely.
¶ Basic Information
You can find basic information of this guidance here.
- Please read this guide carefully. Only by reading it can you ensure the safe use of this equipment.
- These instructions are applicable to installers and users of this equipment.
- Please follow the safety instructions and warnings.
- Please keep these instructions and product information for future reference.
- Please check the equipment first after unpacking. If the device is found to be damaged during transportation, please do not switch on the device.
- If you have any questions, please contact our local after-sales service center or dealer.
- Damage or loss caused by failure to follow the safety instructions, warning labels and installation instructions is not covered by our warranty terms and liability.
¶ Safe Use
Please read the proper use information to ensure that you use this equipment correctly and safely. Please be sure to use this equipment:
- Following the installation instructions and guidance.
- In a well-ventilated and dry environment.
- In proper environmental temperature: 15-30℃.
- In proper relative air humidity environment: 30-70%RH.
- (Recommended altitude: below 1000 meters.)
¶ User Group Restrictions
- Avoid risks that may harm children and vulnerable people.
- People with impaired physical, visual or cognitive abilities.
- People lacking experience, needing supervision or that have not been instructed on how to use this equipment safely.
- Children must not play with this device.
- Keep children and pets away from this device.
¶ Safety Guidance
¶ Warning- Risk of Electric Shock!
- Improper installation is hazardous
- The equipment must be connected and operated in accordance with the nameplate.
- If the equipment is connected to AC power, the power supply must be correctly installed with a grounding plug.
- The protective conductor system of the local electrical equipment must be installed correctly.
- Please ensure that the power system (current, voltage and cables) meets the normal electrical equipment load requirements.
- Don't install an external switch device on the equipment, such as a timer or remote control.
- When installing the device, please check that the cable is not tangled or damaged.
- The power plug and socket must match, the grounding plug must be able to work normally, and the whole machine must be grounded normally.
- If the insulation layer of the power cord is damaged, there is an increased risk of injury and damage.
- Be sure to avoid contact between wires and high-temperature equipment or heat sources.
- Be sure to prevent the wires from contacting sharp points or edges.
- It is prohibited to wind, crush or modify wires.
- If the machine is not properly grounded, the shell may become electrified. If voltage can be detected in the shell, power off the machine and ensure that it is properly grounded.
- If the equipment or wires are damaged, there is an increased risk of damage or injury.
- Do not operate a damaged device.
- Do not unplug the power plug of the device by pulling the wire. Only unplug the power plug of the device by holding the plug body.
- If the equipment or wires are damaged, immediately unplug the power cord or disconnect the indoor power supply.
- To reach after-sales support, please refer to Chapter 1.
- Equipment maintenance can only be performed by trained professionals
- Improper repair can result in injury or damage to the machine.
- Maintenance of equipment can only be performed by trained professionals.
- When repairing equipment, please only use spare parts and accessories originally provided by the manufacturer.
- If the equipment power cord is damaged, only the equipment manufacturer, the equipment manufacturer's after-sales support, or a similarly qualified individual can replace it to avoid any risks.
- The entrance of water vapor may cause electric shock.
- Please avoid exposing the equipment to extreme heat or high humidity.
- Please do not use steam cleaners or spray cleaning equipment.
- Please don't handle electrically powered objects with wet hands.
- If you have any questions, please consult a professional electrician.
¶ Warning-Fire risk!
- It is dangerous to use extension cords and unapproved adapters.
- Please do not use extension cables or multiple power strips.
- If the power cord is too short, please contact after-sales support.
- Please use only the adapter approved by the manufacturer.
¶ Warning-Injury risk!
- Tall equipment may cause injuries when the equipment is lifted.
- Please do not lift the equipment by yourself.
- If you want a transport device, please contact after-sales support.
- The use of non-original spare parts and accessories is dangerous.
- Please only use the manufacturer's original spare parts and accessories.
¶ Warning- Suffocation risk!
- Children may put packaging materials on their heads or wrap themselves in the materials and cause suffocation.
- Please make sure that the packaging materials are kept away from children.
- Please do not let children play with the packaging materials.
- Children may inhale or swallow small parts, causing them to suffocate.
- Please keep small parts away from children.
- Please don't let children play with small parts.
¶ Risk-Harmful health risk!
- Children may lock themselves in the device and put themselves in danger.
- Please do not install the device behind the door, because it may cause the device door to be stuck or unable to open.
- For equipment that will not be used for a long time, please unplug the power cord and cut off the power supply.
¶ Caution -Harmful health risk!
- The device may vibrate during use.
- Place the device on a clean, flat, sturdy surface.
- If pipes and electrical wiring are not laid correctly, this can create a tripping hazard.
- Lay pipes and power cords in a manner that prevents tripping hazards.
- Reaching into the work chamber while the machine's motion system is operating can cause hand injuries.
- Wait until the motion system has come to a complete stop before reaching into the work chamber.
- Some parts of the printer are sharp and can cause injury.
¶ Caution - Risk of Cuts!
- Touching the sharp edges of the device can cause cuts.
- Avoid touching sharp edges.
- Wear protective gloves when installing and transporting the device.
¶ Caution - Risk of Burns!
- The Build Unit 220 and the machine's internal components can become hot during operation or during high-temperature printing.
- Avoid touching the hot build platform.
- Wear the heat-insulating gloves provided in the accessory box when handling the device. Keep children away from the build platform.
¶ Caution - Laser Hazard!
- The laser beam is extremely harmful to eyes and skin and can cause permanent blindness. Always avoid direct contact.
¶ Caution - Gas Hazard!
- The Raise3D RMS220 series can optionally use nitrogen as an inert gas atmosphere.
- Avoid any exposure to oxygen-deficient environments.
- Exposure to oxygen-deficient environments can cause coma or even death.